PE 100-RC cooling water pipes

For a steam power plant in Finland, operated by „Porvoon Energia“, a solution had to be found to replace the extremely corroded steel pipes for the transport of cooling water efficiently and quickly. The medium to be transported is sea water. It is known for its high corrosion potential of metals and has impressively demonstrated this with the existing steel pipeline after only 4 years in operation.

Sketch of the pipeline
Fig. 1 Sketch of the pipeline for the cooling water supply.
Removed steel piping components
Fig. 2 Removed steel piping components which can no longer be used due to severe corrosion.

What is corrosion?

Corrosion is an electrochemical reaction of a material with its environment, which leads to a change in the material. The type of corrosion can be chemical, electrochemical or metal-physical.

Which factors decisively influence the corrosion rate?

The following factors are decisive for the corrosion rate and influence it immediately:
•    The more reactivity of a metal, the higher the probability of corrosion.
•    Any impurities accelerate the rate of corrosion.
•    Water and electrolytes (e.g. salt) contained in it, as well as higher temperatures increase the corrosion rate.
•    Coatings of the metallic surface with materials that are more active than the metal itself can delay the corrosion rate (e.g. zinc).

Consequences of corrosion in pipelines:

The effects and degree of corrosion in a piping system vary according to the application and material quality, and depend heavily on the factors mentioned above. In most cases, corroded piping systems are subject to the following problems:
•    In some cases the cross-section and thus the flow rate can be reduced by incrustations, in which case more pump capacity is required and operating costs increase.
•    Contamination of the liquid to be transported by particles that are detached.
•    The pipe walls corrode and become thinner. The pressure resistance decreases as a result.
•    Leakages are the further consequence. High costs due to water damage.

PE corroded metallic pipelines
Fig. 3 Examples of corroded metallic pipelines.

A trend becomes apparent:

A large part of the pipelines currently in operation for seawater or saltwater applications are generally made of high-quality stainless steel, galvanised steel or cast iron. These materials are widely referred to as „saltwater resistant“, but are subject to corrosion over time, which inevitably leads to high maintenance costs and even plant failure/downtime.

For some years now, however, the trend has been towards plastics. Especially under seawater conditions, the service life of thermoplastic materials, which offer excellent corrosion resistance, is many times longer. Due to the very smooth surface of e.g. PE 100-RC pipes, particles find it very difficult to adhere and therefore hardly any deposits are formed.

PE 100-RC underwater installation
Fig. 4 PE large diameter pipe from AGRU, connected with stainless steel flanges.
PE 100-RC underwater installation

The corrosion resistant material

After detailed consideration and planning, it was decided to replace the corroded steel pipelines with PE 100-RC pipes and fittings. The requirements regarding temperature and pressure, including the calculated safety margins, are met with an SDR 11 (PN 16) system. In addition, easy installation and low material costs were factors that ultimately influenced the decision.

Below are just some of the advantages of PE100-RC pipe systems:
•    High flexibility, low weight
•    Homogeneously weldable, UV resistant
•    Very good chemical resistance
•    Resistant to weathering, long service life
•    Perfect abrasion resistance and resistance to pressure shocks
    (up to 200 % of the nominal operating pressure)
•    Use also at very low temperatures (application range -40 °C to + 60 °C)
•    Physiological harmlessness

PE for more than 40 years
Fig. 6 PE pipeline part which has been in operation for more than 40 years. There is no wear and no corrosion. The thermal and mechanical properties of the pipe and the welded joint have been determined by countless tests carried out by AGRU. The values correspond to a new PE 80 pipe.
Ready installed pipeline
Fig. 8 Ready installed pipeline made of PE 100-RC.


The planning and laying of the new AGRU PE 100-RC pipeline was carried out by the experienced Finnish company Atolli. AGRU PE 100-RC heating coil fittings were used for welding the pipeline sections.
The installation was carried out on schedule within a few working days and the power plant was put back into operation.

AGRU shaped heating coil parts
Fig. 7 AGRU shaped heating coil parts.

Forward to the Product Catalogue

Like us 

Agru on Facebook Agru on YouTube

Follow us 

Agru on linkedIN

Agru on Instagram

Agru on Vimeo

Register for our Newsletter